SERVICES
What We Do
From mechanical installation to full electrical automation design, ISA Professionals delivers end-to-end industrial solutions — concept through integration, anywhere in the world.
Mechanical & Electrical Installation
Complete mechanical and electrical installation services for industrial process equipment. We handle the full scope — from rigging and setting equipment to final electrical connections and commissioning.
Get in touchCAPABILITIES
- Pneumatic conveying systems
- Dust collectors and baghouses
- Divert valves and rotary valves
- Mixers and blenders
- Process piping and ductwork
- Motors, drives, and power distribution
Automation & Controls Design
Full electrical automation design from concept to integration. We engineer control systems that improve efficiency, reliability, and safety across your entire operation.
Get in touchCAPABILITIES
- PLC programming and integration
- HMI design and development
- Control panel design and fabrication
- Variable frequency drives (VFDs)
- Instrumentation and process control
- SCADA and remote monitoring
Troubleshooting & Repair
Fast, accurate diagnosis and repair of industrial electrical and mechanical systems. When your operation goes down, we respond — 24/7 emergency service available.
Get in touchCAPABILITIES
- Electrical fault diagnosis
- PLC and controls troubleshooting
- Drive and motor diagnostics
- Pneumatic system troubleshooting
- Preventive maintenance programs
- 24/7 emergency response
CORE SPECIALTY
Dust Collection & Pneumatic Conveying Specialists
Most electrical contractors can wire a panel. Few understand what happens inside a dust collector or why a pneumatic conveying line loses velocity at the terminal. ISA Professionals was built around these systems — it's where 20+ years of field experience is concentrated.
Dust Collection Systems
We install, automate, and troubleshoot baghouse dust collectors, cartridge collectors, and cyclone separators for bulk material handling, woodworking, food processing, and chemical facilities. From pulse-jet timer controls and differential pressure monitoring to full PLC-based automation with remote alarming — we handle the electrical scope end to end.
- Baghouse and cartridge collector installation
- Pulse-jet solenoid wiring and timer controls
- Differential pressure monitoring and alarming
- Fan motor and VFD integration
- Rotary airlock and diverter valve controls
- Compliance with NFPA 654 and OSHA dust hazard requirements
Pneumatic Conveying Systems
Pressure and vacuum pneumatic conveying systems require precise electrical integration to run reliably. We commission new systems, retrofit aging controls, and troubleshoot performance issues — plugged lines, inconsistent throughput, blower surging — tracing faults from the source to the terminal.
- Dilute and dense phase conveying system controls
- Blower and compressor motor wiring and VFD setup
- Divert valve and rotary valve sequencing
- Pressure and vacuum transducer integration
- Filter receiver and cyclone separator controls
- System commissioning and performance verification
Common Questions
Do you install dust collection systems?
Yes. We handle the full electrical scope for dust collection system installations — from motor and VFD wiring to pulse-jet controls, differential pressure monitoring, and PLC automation. We work with all major collector manufacturers and can integrate new systems into existing plant controls.
Can you troubleshoot a pneumatic conveying system that keeps plugging or losing throughput?
Absolutely. Pneumatic conveying problems are often electrical in origin — a failing VFD, a mistuned pressure setpoint, a stuck divert valve, or a sequencing issue in the PLC. We diagnose the full system, not just the obvious failure point, and we've resolved conveying problems that other contractors couldn't find.
Do you work on existing systems or only new installations?
Both. We retrofit and upgrade existing dust collection and pneumatic conveying controls as often as we install new systems. If your equipment is running on aging relay logic or an obsolete PLC, we can modernize the controls without replacing the mechanical equipment.
What industries do you serve?
We work across industries that move bulk materials — food and grain processing, chemical and pharmaceutical manufacturing, woodworking and wood products, plastics, mining, and general industrial. If it has a dust collector or a pneumatic conveying line, we can help.
Do you travel for projects?
Yes. We serve clients across the U.S., Canada, Mexico, and internationally. Travel is standard for us — we go where the work is.
Our Approach
Every project follows a proven process — from the first conversation to final commissioning.
Assess
We start by understanding your operation, your goals, and the specific challenges you're facing.
Design
Our team develops a detailed plan — electrical schematics, control logic, equipment specs, and installation scope.
Execute
Skilled installation and integration work, performed safely and efficiently with minimal disruption to your operation.
Commission
Full system testing, startup support, and documentation — we don't leave until everything runs right.
Ready to Start a Project?
Tell us what you need. We work with clients across the U.S., Canada, Mexico, and globally.
Contact Us